螺旋鳍片管换热过程三维数值模拟及性能评价

作者：张宪1，石林1，张意2，钟江1 日期：2008-12-26/span> 浏览：4039 查看PDF文档

螺旋鳍片管换热过程三维数值模拟及性能评价

张宪1，石林1，张意2，钟江1
(1.浙江工业大学 机械制造及自动化教育部重点实验室,浙江 杭州 310014;2.浙江大学 竺可桢学院，浙江 杭州 310058)

摘要：基于三维有限元模型，采用ANSYS的二次开发语言APDL编写仿真程序，对工作在锅炉省煤器中的螺旋鳍片管的换热特性进行了数值模拟。基于仿真模型分析了管内冷水速度、管外烟气温度变化对螺旋鳍片管换热性能的影响。提出了一种以热流边界层宽度及温度梯度为依据进行定性分析，以传热效率为依据进行定量分析或优化设计目标函数的螺旋鳍片管三维仿真结果评价方法。研究结果表明，为基于有限元分析技术进行螺旋鳍片管换热器的结构优化设计奠定了基础。
关键词：螺旋鳍片管；热-流耦合；数值模拟；换热特性评价
中图分类号：TK223.3文献标识码：A文章编号：1001-4551(2008)11-0079-04

Three-dimensional numerical simulation and performance evaluation of heat transfer of spiral finned tube
ZHANG Xian1, SHI Lin1, ZHANG Yi-chong2, ZHONG Jiang1
(1.The MOE Key Laboratory of Mechanical Manufacture and Automation, Zhejiang University of
Technology, Hangzhou 310014, China; 2.College of ZHU Ke-zhen, Zhejiang University, Hangzhou 310058, China)
Abstract: The heat transfer characteristic of spiral finned tube which performed in heat recovery boiler was simulated by using programmable language “APDL” of ANSYS. The influence of different cold waters rate and the smokes temperature was analyzed based on simulation model. A way of evaluating the 3D simulation results of spiral finned tube was put forward, which based on the qualitative analysis of thermal convection boundary layer and temperature gradient, and the quantitative analysis of heat transfer efficiency or objective function for optimum design. The experimental results show that, it could give reference to structure design and optimization.
Key words: spiral finned tube; heat-flow coupling; numerical simulation; estimate of heat transfer characteristic
参考文献(References):
［1］PAISARN N, MANACHAI N. Tube side heat transfer coefficient and friction factor characteristics of horizontal tubes with helical rib［J］. Energy Conversion and Management,2006,47(18):3031-3044.
［2］SRBISLAV B G, BRANISLAV  M J. Research on air pressure drop in helically finned tube heat exchangers［J］. Applied Thermal Engineering,2006,26(5):478-485.
［3］袁益超，刘聿拯，曹建光.螺旋鳍片管束传热与阻力特性研究的现状与发展［J］.动力工程，2002,22(5):1922-1927.
［4］任洪娟,刘爱萍.基于PHOENICS螺旋翅片管的数值研究［J］.山东理工大学学报:自然科学版,2004,18(6):61-63.［5］张永军，李言.翅片管换热过程的数值模拟［J］.机械强度,2004,26(4):466-468.
［6］童鲁海.H形鳍片管传热性能的三维数值模拟计算[J].机电工程，2007，24（10）：79-81.
［7］田林,罗来勤,王秋旺.两种内翅片管对流换热与阻力特性的实验研究［J］.工程热物理学报,2005,26(3):471-473.