基于双谱分析的齿轮故障诊断方法

作者：蒋宇1，李志雄2，李力2 日期：2008-12-26/span> 浏览：3296 查看PDF文档

基于双谱分析的齿轮故障诊断方法

蒋宇1，李志雄2，李力2
（1.黄山学院 信息工程学院，安徽 黄山 245013;2.三峡大学 机械与材料学院，湖北 宜昌 443002）

摘要：齿轮啮合过程中的振动信号往往呈现出非线性、非高斯性，加上强噪声的干扰，给故障特征的提取带来了较大的困难。为实现齿轮单一故障的分类和诊断，采用时序参数化的双谱分析方法，对齿轮故障模拟试验台上采集的正常状态和3种故障状态的振动信号进行了分析，根据双谱谱峰的分布及数目的差异性，实现了齿轮正常、裂纹、磨损、剥落4种状态的识别和分类。结果表明，双谱分析可以抑制背景噪声，并有效提取信号中的非高斯成分，是一种有效的故障诊断方法。
关键词：齿轮；双谱分析；参数估计；故障诊断
中图分类号：TH132文献标识码：A文章编号：1001-4551(2008)11-0083-04

Bi-spectrum analysis method for gear fault diagnosis
JIANG Yu1, LI Zhi-xiong2, LI Li2
（1.College of Information Engineering, Huangshan University, Huangshan 245013, China;
 2.College of Mechanical and Material Engineering, China Three Gorges University, Yichang 443002, China）
Abstract: The non-linear and non-gaussian properties of vibration signals are usually exhibited in gear meshing. It made the extraction of fault feature difficult plus the strong noises influence. In order to classify and diagnose gear single fault, firstly normal and three different abnormal vibration signals were collected on simulant experiment table. Then the bi-spectrum estimated with time series parameters method was adopted for diagnosing. Finally four modes of normal, crack, wear and spalling were effectively classified and diagnosed, according to the number and distribution of spectrum peaks. The results show that noises can be inhibited and non-gaussian can be extracted by bi-spectrum, and bi-spectrum analysis is efficient method for gear diagnosing.
Key words: gear; bi-spectrum analysis; parameter estimation; fault diagnosis
参考文献(References):
［1］张桂才，史铁林，杨叔子.基于高阶统计量的机械故障特征提取方法研究［J］.华中理工大学学报，1999，27(3):6-8.
［2］CAILLEC L, MARC J, RENE G. Comparison of statistical indices using third order statistics for nonlinearity detection［J］. Signal Processing,2004,84(3):499-525.
［3］王凯，张永详，李军.齿轮裂纹故障的双谱分析［J］.机械强度，2006，28（3）:346-348.
［4］ZHAO Shou-guo, WANG Su-pin, ZOU Yuan. Study on non-gaussian ARMA model and bi-spectrum of lung sounds［J］. Journal of Xi an Jiaotong University,2001,35(4):355-359.
［5］郑海波，陈心昭，李志远.基于双谱的齿轮故障特征提取与识别［J］.振动工程学报，2002，3(15):354-357.
［6］姚天任，孙洪.现代数字信号处理［M］.武汉:武汉科技大学出版社,2003.
［7］张贤达.时间序列分析—高阶统计量方法［M］.北京:清华大学出版社,1996.
［8］李勇,徐震.Matlab辅助现代工程数字信号处理［M］.西安:西安电子科技大学出版社,2002.